SailBlogs
Bookmark and Share
Calou's Blog
Cruising with the crew of CALOU on the Baja Ha-ha and Pacific Puddle Jump
the latest news
Bruce
10/17/2006

Anderson's put the boat back in the water today, and stepped the mast. Their diesel mechanic began the checkout of the engine. They recommended replacement of the raw water pump with new, which I ordered.

An unanticipated glitch, is that they poured the new Spar-Tite (this is an epoxy plastic that fills the gap between the mast and the deck), and Spar-Tite recommends 48 hours cure time before the rigging is tensioned. So this means another two days before they can tension the standing rigging. This pushes us back another day, but, oh well, there's nothing we can do about that now.

With the mast back in, I re-connected all the mast electronic cables (radar, masthead instruments, and mast lights).

| | More
10/19/2006 | Bruce
I guess 48 hours wasn't needed, because they tensioned the rig 24 hours later (much to my relief).
Are we lost yet?
10/16/2006

Well, WE aren't!

| | More
First picture DIRECTLY from CALOU
10/16/2006

Here's a photo from CALOU! A bit blurry, but who wouldn't be after that bon voyage?

| | More
we're getting there...
10/16/2006

last Friday we found a small leak at the rudder post, what used to be a grease fitting had corroded. This was fixed this morning.

I laid out the new anchor rode today - 200 feet of chain plus 100 feet of nylon rode and painted it with yellow and black markings every 20 feet.

Then I raised the entire thing into the anchor chain locker using the new electric windlass.

I used the Sawzall to cut away the excess wood around the mast partners, so that when the new Spartite is poured, it will not stick to the deck the next time. The edges were coated liberally with Vaseline.

Tomorrow, the boat will be put back in the water and we'll step the mast.

| | More
Cockpit shower
10/16/2006

There was one item that was considered a "comfort" item, placed in last priority. The cockpit shower. It lets us rinse things, and ourselves, before entering the cabin. It will be great for the two boys and their sandy legs and shoes.

| | More
10/16/2006 | Ori Lahav
usually people put them on the transom.
10/16/2006 | Bruce
well, it depends on the boat configuration, I guess. To mount it on our transom would be totally impractical.
10/17/2006 | Ori lahav
ohhh - you probably dont have a swimming deck back there. - got you.
AC Inverter Installation Completed
Bruce
10/15/2006

The AC Inverter has been installed; it works like a charm. When running the blender, the draw on the 12 volt circuit was 12 amps. It'll be great to have on-demand AC power.

| | More
How to send us email via our SSB radio
10/15/2006

Friends,

You can send us e-mail that we can receive via our Single Sideband (ham) radio while at sea. This will work even when we're miles offshore. The limitation is that, due to the limitations of SSB radio, the files must be PLAIN TEXT and contain no file attachments (ie, no photos). Also you must promise not to post the email address on any web sites, web pages, or other publications where spammers might find it.

For instructions on how to send us an email, first send a blank email message to: sailmailinfo (at) calou (dot) com. This address is an autoresponder that will reply back to you with the instructions.

| | More
AC Inverter
10/14/2006

Started installation of a Xantrex 1000 watt AC inverter today. I wasn't going to get one but they're so cheap these days and it'll be easier to keep things like cell phones, cameras and ipods charged. And we'll be able to run our Seal-a-Meal vacuum food bagger which will come in very handy. We may even bring the blender. This inverter is hardwired into the boat's AC system so it automatically switches over from Shore Power to Inverter mode when the shore power is disconnected.

| | More

Newer posts ]  |  [ Older posts ]

 

 
Powered by SailBlogs