SailBlogs
Bookmark and Share
Issuma
Mossy Trees
Richard
Thu Nov 3 17:38:45 EDT 2011, Yakutat, Alaska

The rarely-ending rain in Yakutat results in moss growing on the trees.

Sat Nov 5 17:30:51 EDT 2011 | Terry
we all know ... trees ... moss on the north side ... go south ... the other side with no moss ... hehehehe
Warm Hands
Richard
Mon Oct 31 19:20:43 EDT 2011

I used a variety of gloves and mitts this year in the NW Passage. This is what I found to be useful for cold-weather sailing.

As a general rule, insulated gloves of various kinds work well in temperatures 8C/45F and above. For colder temperatures, mitts are the only things to keep hands warm.
Note that I don't pull on ropes with any of these gloves or mitts--I don't think any of them will last long if used for pulling hard on ropes with. As most of ones time is not spent pulling on ropes, it isn't much of a problem to remove gloves/mitts to pull on ropes (reef/tack/gybe/etc), then put the gloves/mitts back on to warm back up.

Sealskin Mitts with Felt Lining (top left):
Not generally found in stores, I got these in the Northwest Territories many years ago. One of the mitts is now missing the (removable) felt liner--otherwise, these would have been the warmest mitts I had. Excellent for keeping the hands warm (especially with a spare set of liners so one can be drying below while the other is in use), and very easy to get on and off. Too hot to be worn above 10C/50F.


Rabbit Fur Mitts with Polyester Insulation (middle left):
These are made in China, and sold in Canada (and probably USA) at outdoor equipment stores for about $30. They are the warmest mitts I had aboard. Even when moderately wet they were still warm (though when it rained a lot, I switched to the blue insulated rubber gloves). Too hot to be worn above 10C/50F.


Insulated Yachting Gloves (top right):
I got the West Marine insulated gloves several years ago and never used them until this year. They work well in mild temperatures, and are a bit warmer than the insulated rubber gloves when it isn't really wet. Quite comfortable to steer with. Warm down to about 8C/45F.


Blue Insulated Rubber Gloves (middle right):
I got a pair of these in Rimouski, Quebec for about $10. I only bought one pair because I wrongly figured I could buy another pair along the way at any fishing supply store. It wasn't until Alaska that I found another pair. Excellent in wet weather, and warm to about 8C/45F. Loose and stiff enough to be easy to take on and off. They take a long time to dry the insulation out, though, so best to have more than one pair.


Green Plastic Gloves with Separate Cotton Liners (bottom):
In Cartwright, Labrador, I was told all the fishermen had switched to using waterproof gloves with separate liners, that way, when the liners got wet, they just changed liners. Though I'm sure it worked for the fishermen, I didn't find this combination all that useful. This combination did work, but it takes a while to take off both an outer and inner glove, so didn't work all that well with my habit of taking off gloves/mitts before pulling on ropes. If I only took off the outer glove (which was easy), then I'd wet the cotton liners handling the wet ropes (and wet cotton has no insulation value). This system would work better if one had enough of the outer gloves aboard that one could just wear the gloves while handling ropes, let the gloves wear out and replace the gloves as they wore out (buying replacements as you go along is not practical in the NW Passage, where you can't rely on being able to buy anything, so if you don't have it with you, you may need to do without it).

Tue Nov 1 13:48:43 EDT 2011 | Amos
Looks like you may get a weather window Wednesday or Thursday? Fingers crossed.

The South awaits!
Wed Nov 2 0:46:14 EDT 2011 | Victor
Very good review and worth publishing. Many people just neglect that. Good work.
Thu Nov 3 14:35:09 EDT 2011 | Amos
.Today...NE wind 25 kt diminishing to 15 kt in the afternoon. Out of Disenchantment Bay...gusts to 40 kt in the the morning. Seas 3 ft building to 5 ft in the afternoon. .Tonight...NE wind becoming 20 kt late. Seas 4 ft. Rain and snow late. .Fri...Se wind 20 kt. Seas 7 ft. Rain. .Fri night...E wind 15 kt. Seas 7 ft. Rain. .Sat...SW wind 10 kt. Seas 6 ft. Rain. .Sun...SW wind 10 kt. Seas 6 ft. .Mon...E wind 20 kt. Seas 7 ft.

Is this feasible? Chewing nails...
Fri Nov 4 17:35:01 EDT 2011 | Richard Hudson
Thanks, Victor.

Amos, thanks, that was the Yakutat Bay forecast you are quoting. The ones to look at for the coastal route are the Cape Edgecumbe to Cape Fairweather and Cape Fairweather to Icy Cape. Those forecasts (east 30-50 knots) were not quite good enough for Issuma for Wed/Thursday.
Sun Nov 6 15:59:17 EST 2011 | Amos
Thanks, Richaed, quite right. Those coastal stretches do look nasty. Thanks for the correction. Here's hoping you get the break you need soon!
Shaggy Sails
Richard
Sat Oct 29 18:00:00 EDT 2011, Yakutat Bay, Alaska

Imvubu sailing ahead of Issuma (picture taken Oct 17).

The edges of the sails that are set on Issuma have tattered cloth hanging off them. The tattered cloth is the remnants of the ultraviolet protection cloth that is put on roller furled sails (so the sails are shielded from UV when they are furled). The cloth that is typically used for UV-protection on sails (sunbrella) has poor resistance to abrasion. The cloth has been abraded by rubbing against rigging wires when tacking. While the UV-protection cloth does need to be replaced (preferably with something more durable), one of the advantages of sailing in an area where it is cloudy and rainy most of the time is that there is hardly any UV around to damage things, so this repair can wait :).

I'm not entirely sure how I'm going to fix the UV-protection on these sails--I'd like to find a more durable cloth (maybe in black so it definitely blocks UV?) and probably glue it on (no stitches to get abraded away).

Sat Oct 29 20:37:48 EDT 2011 | Doug
Suggestion - when you post and use a picture make sure it accurately depicts the information displayed - SV IMVUBU is actually in Juneau AK - from your Yakutat Bay dated post and picture it appears SV IVUBU in in Yakutat with you.
Glad to see your are posting often - keep them coming. When I see you next month I'll suggest several sailmakers with furler cover solutions.
:-)
Doug
Sat Oct 29 22:58:42 EDT 2011 | Victor
Black, no luck. It will absorb all UV in no time. Try old fashion cotton and that has to be stitched in place. I am sure you are celebrating ghosts of Halloween at Juneau with Ralf tonight while Maggie is the Ghost of Alaska. Cheers, Victor
Sun Oct 30 17:15:26 EDT 2011 | terry
looks like a race .... who will be first .... south ... ???
Mon Oct 31 18:00:23 EDT 2011 | Jerry Levy
You could try sending an email to Sailrite and ask them about sunbrella alternatives.
Mon Oct 31 19:17:36 EDT 2011 | Richard Hudson
Thanks for the comments.

Doug, that's a good point, I'll be more careful with the implications of the dates I post. I'd definitely like to talk to sailmakers with an idea for something other than the standard sticky-back sunbrella for UV protection.

Victor, I was thinking in terms of gluing a UV protection strip on (I repair sails with polyurethane adhesive sealant and it works well), as stitches get chafed and don't tend to last long. Not sure I understand what you mean about black--isn't anything black likely to block all UV?

Terry, being the boat behind the other boat, I will of course say it was not a race :).

Jerry, thanks for the suggestion, I will email them.
Mon Oct 31 19:25:34 EDT 2011 | Richard Hudson
Thanks for the comments.

Doug, that's a good point, I'll be more careful with the implications of the dates I post. I'd definitely like to talk to sailmakers with an idea for something other than the standard sticky-back sunbrella for UV protection.

Victor, I was thinking in terms of gluing a UV protection strip on (I repair sails with polyurethane adhesive sealant and it works well), as stitches get chafed and don't tend to last long. Not sure I understand what you mean about black--isn't anything black likely to block all UV?

Terry, being the boat behind the other boat, I will of course say it was not a race :).

Jerry, thanks for the suggestion, I will email them.
Tue Nov 1 15:02:02 EDT 2011 | Amos
You may want to look into carbon-fiber matting for the edging you need.
Wed Nov 2 0:43:47 EDT 2011 | Victor
Black absorbs heat and UV the most. White is the best choice. May be NWP UV was so intensive. Stitching I know is not good for the longer run.
Fri Nov 4 16:36:25 EDT 2011 | Richard Hudson
Hmmm, so you mean it is better to try to reflect the UV with white than to absorb it with black.

I doubt there was all that much UV in the NWP -- skies were mostly cloudy as I recall. Chafing the wire stays seems to be what did in the sun protection cloth.
Bergy Bit
Richard
Fri Oct 28 20:44:05 EDT 2011, Yakutat Bay, Alaska

Bergy bit with a hole big enough to kayak thru (except for the extreme danger that doing so would present if the ice rolled over).

Disenchantment Bay
Richard/Maggie
Thu Oct 27 18:59:16 EDT 2011, Yakutat Bay, Alaska

In 1792, Alessandro Malaspina, an Italian nobleman and Spanish Naval officer, was looking for the Northwest Passage for the King of Spain. Sailing up Yakutat Bay until stopped by the ice from the glaciers, he named the NE part of Yakutat Bay Puerto del Desengano (Disenchantment Bay).

Fri Oct 28 5:53:55 EDT 2011 | will
i love the series . . the saga, actually. how cold was it here? are bergys any danger for issuma's hull?
Fri Oct 28 11:28:13 EDT 2011 | AMos
Great photo, Maggie--that salty grim determination in Richard's face is classic!!
Fri Oct 28 16:38:34 EDT 2011 | george ray
Are the berry bits a danger to the propellers?
Fri Oct 28 17:51:26 EDT 2011 | Terry
buuurrrr .... looks cold ... time to go south .... put the pedal to the metal !!
Fri Oct 28 20:35:41 EDT 2011 | Richard Hudson
Thanks for the comments.

I don't recall the temperature...definitely above freezing so not really cold , probably about 5C/40F. Temperatures have dropped in the last week, and are much closer to freezing now.

The growlers and bergy bits aren't really a danger to the hull, at least at low speeds and in low concentrations. The hull is designed to handle a lot of ice pressure, and to be forced up in the case of a lot of pressure (rather than be crushed), but there are no ice ratings for yacht-sized vessels.

The ice is definitely a danger to the propellers if they hit a big piece (which doesn't move fast out of the way) or if a piece gets between hull and prop so prop blade takes a big load. With no/light winds and daylight, when able to see the ice and stop the propellers before they hit it, there is no problem.

As for going south, we're all for the idea--just waiting for the wind to do something other than strong to storm-force headwinds for long enough to get down the coast and inside :).
Bergy Bit
Richard/Maggie
Wed Oct 26 21:16:46 EDT 2011, Yakutat Bay, Alaska

Bergy bit from Hubbard Glacier.

Growlers
Richard/Maggie
Wed Oct 26 21:14:59 EDT 2011, Yak

Growlers in front of the Hubbard Glacier.

Thu Oct 27 8:16:54 EDT 2011 | Amos
Wow--makes me nervous just looking at it. How thick is Issuma;s hull?
Thu Oct 27 19:03:08 EDT 2011 | Richard Hudson
Issuma's hull is 6mm thick below the waterline, and 4mm higher up. The plates are overlapped, and fully welded, so the hull is quite strong.
Hubbard Glacier
Richard/Ralf
Mon Oct 24 19:41:52 EDT 2011, Yakutat Bay, Alaska

The Hubbard Glacier is the longest tidewater glacier in Alaska. We sailed and then motored up Yakutat Bay to have a look at it.

Tue Oct 25 17:04:14 EDT 2011 | Timothy
Super cool that you have shots of the boat underway without having to park yourself on a stray iceberg and then swim fast to catch up.

And are those growlers or bergie bits in the foreground? (the white pieces in the water, not the humans aboard)
Tue Oct 25 22:23:57 EDT 2011 | Victor
So you were only 10 nm from Canadian border. Turner, Hoenke, Hubbard Glaciers and some more off Russell Fiord contribute to that. Didn't mention ahead of time of real dangers there e.g. "Extreme currents occur at the pass between Russell Fiord and Disenchantment Bay. These currents are extremely fast and treacherous carrying large icebergs. The pass is deemed unsafe and not navigable by mariners." NOAA US Coastal Chart 16761.
Tue Oct 25 22:31:47 EDT 2011 | Andy
We seem to have lost track of you. Nanci Sez it's howling right now in Hoonah so I expect that you are.... where? Grays harbor?

Looks like Ralf is in Juno giving a talk at the Prospector on Wed. If you go to Juno, I have a 5000# anchor/buoy/dock you can use.

I'm in Arizona 'til 11/17 so I'll miss you.
Wed Oct 26 15:49:59 EDT 2011 | Brian Lumley
Richard;
Good to see you are making progress down the coast before the winter sets in. Are you planning on wintering in BC? My friend Bob McDonald, I believe you met him at Bluffers last year, is now living in Victoria. I will be seeing him soon and will let him know about your successful journey. Let me know when you are in good email territory and I will send you my latest horrific tale from Lake Ontario.
Brian
Wed Oct 26 16:50:05 EDT 2011 | Richard Hudson
Thanks for the comments.

Timothy, thanks, the small ice pieces in the foreground are growlers. Growlers are pieces of ice less than 5m (15') long, bergy bits are 5m to 15m(49') long.

Victor, yes, Canadian border is quite close by, but not by water. That pass between Russel Fjord and Disenchantment bay is something I was trying to avoid, as it certainly does seem difficult.

Andy, sorry I will miss you when I do get south. I am still in Yakutat--weather hasn't been quite good enough for Issuma (Ralf has a significantlyfaster speed under power, so he was able to make it out when I was not) to make it past Cape Spencer before the next lows yet. I came close to being in Graves Harbor for the current storm, but didn't feel I had enough time to prepare for the storm in an anchorage I'd never been to before. Thanks very much for the offer of your mooring.

Brian, I'm actually just late enough that winter seems to have set in :). I have pretty good internet access at the bar here most days, and would like to hear your story.
Sailing in Yakutat Bay
Richard/Ralf
Tue Oct 18 18:15:59 EDT 2011, Yakutat Bay, Alaska

Yakutat Bay is beautiful. As could be expected for Alaska in October, it rains a lot.

The Facnor furler was giving problems (it is fixed now), so we weren't using the main staysail.

Fri Oct 21 1:41:33 EDT 2011 | yann
nice boat, isn't she? :)
Fri Oct 21 4:23:47 EDT 2011 | george ray
What problems with the Facnor??
Mon Oct 24 12:59:50 EDT 2011 | Amos
Currently(10-24) high-wind advisories:

"* WIND...SOUTHEAST WIND 25 TO 40 MPH WITH GUSTS POSSIBLY REACHING UP TO 60 MPH OR HIGHER.

* TIMING...WINDS WILL BE INCREASING TUESDAY STARING IN YAKUTAT AND SPREADING DOWN THE OUTER COAST THROUGH THE DAY. PEAK WINDS WILL BE LATE TUESDAY AFTERNOON INTO TUES EVENING BEFORE DIMINISHING LATE TUESDAY EVENING.

Stay safe!


A
Mon Oct 24 20:19:45 EDT 2011 | Richard Hudson
Thanks for the comments. Yes, she is a nice boat :).

The problem with the furler was that the stay needed tightening. The way they made the furler, adjusting the stay requires disassembling the drum (six pieces), so it is a job that tends to get delayed.

The weather in the Gulf of Alaska is generally windy, so waiting for a good time to move south is taking quite a while :).
Sailing in Yakutat Bay
Richard/Ralf
Mon Oct 17 18:08:51 EDT 2011, Yakutat Bay, Alaska

We are waiting in Yakutat for a change in the weather. My friend Ralf on Imvubu (www.yachtimvubu.com) has been doing the same. We went sailing up Yakutat Bay to have a look at the glaciers (the weather in Yakutat Bay is often much different than the weather outside), so Ralf took this picture from his boat.

Fri Oct 21 4:22:33 EDT 2011 | george ray
Thanks to Ralf for his great website!!

Newer ]  |  [ Older ]

 

 
Powered by SailBlogs