We changed our mind and made for Mana Island where we will be for a couple of days. Very tight channel getting in and we're glad one of the tour boats was coming in in front of us and lead the way. Out here, the buoys are "left red heading in" not "red right returning" as it is in the US. So it can get confusing.

We'll be here a few days before we head over to "Treasure Island"(not it real Fiji name). Then back to Vuda Point. We have to be back by the 22nd as our Vodefone internet bill is due. Oh the pressure of civilization.

Comments [1] | | More

Here we are at Musket Cove now sitting on our anchor after one night on a buoy. We came out from Vuda Point Marina on Thursday(never leave on a Friday, let alone the 13th)to get away and do some scuba diving and relax. Plus we wanted to install the new anchor and where better than when you are away from the dock.

We left Vuda about 1015 and got into Musket Cove just before 1300 and grabbed one of the many buoys out here. It's off season so there are plenty to choose from. Once attached to the buoy, we launched Puff, our dingy, and got ready to work on the anchor. First we tried to undo the shackle that holds the old one to the swivel on the chain. I cut the seizing wire and got a crescent wrench and tried to turn it. No go. It was locked in place. There was enough corrosion on not only the shackle and the swivel, but the high tensile steel chain looked a mess also. I though this was supposed to be tough stuff. I put on some lubricant and waited a few minutes and tried again. Still no go. Out with the hack saw. Half an hour later, and a very bent blade, it came loose. Glad I put a rope on the old anchor as it was heading off the bow once the chain was off. We hooked the new anchor to the block and tackle that we use to raise and lower Puff. I pulled out the old anchor(60 pounds) and lowered it into the dingy. Tracy lowered the new anchor into Puff and then pulled the old anchor back up so I'd have some space to move around. Let me tell you, that new Rocna anchor takes up a bunch of space. I hooked the new anchor to the swivel with a new slightly smaller shackle(all we had)Tracy pushed the button that hauls in the chain and up it went. Well, almost. Up it went till the chain jumped off the teeth of the windlass and the long shank jammed against the steel bolt that goes through the bow rollers. It was up but far from secure. OK, lets take off the steel bolt so we can get the entire anchor aboard. It's held on with nuts on the end that screw on with a cotter pin through it so it doesn't unscrew. New problem. The pin was corroded clear down to the flat surface of the nut. That's what happens when you don't use stainless steel cotter pins. I tried pounding it out with an awl and hammer but no luck. As it was the end of the day, we decided to just let it sit(not going any where)till Friday. I did manage to get the chain back in the teeth of the windlass though. We climbed into Puff and went ashore to get checked in and pay for our one night on the buoy.

Friday, I pulled out my drill and drilled out the cotter pin as the punch wasn't going to do it. With it out, that problem was solved. Now we will have to have a stainless steel fabricator come out and make a new attachment for the bow roller so the anchor will fit. We dropped the buoy line and headed over to the anchorage area where we dropped our new Rocna. She went down like a rocket taking lots of chain with her. We ended up in about 50 feet of water. We let the wind correct our position so we were down wind of the anchor and then Tracy hit the reverse lever and we backed down and the anchor set. At least Zephyr stopped really quick. I haven't gone down there yet with our scuba gear, but we haven't move since. In the afternoon, we took off for a local snorkel spot as the wind was still blowing and the rain clouds looked a bit dark on the bottom. It had been that way all day which is why we hadn't headed out for a dive. It did rain a bit as we snorkeled but not really that much. The place we went is a favorite for vacationers here and we had a good many tourists gliding along with us in the blue water.

Once we were done, we headed back for Zephyr where Tracy made a great dinner of pork tenderloin in a mushroom sauce and shell macaroni(bought in Mexico). Add in a nice bottle of white wine and it was a great meal. After dinner, we fired up our computer and watched a movie.

We headed out to Plantation Pinnacle to scuba dive there again. There are supposed to be three tall bommies(tall coral heads) though we had only found one. When we got to the GPS spot I had marked on our last trip, the buoy(Prestone antifreeze jug) we tie up to was gone!! There was no place to tie up to and you don't what to drop and anchor(didn't have it with us anyway) as you don't want to damage the coral. After looking around(Tracy's head in the water as I drove Puff) we finally gave up and came back to Zephyr. From what Tracy said, the visibility was rotten. Only about a 20 foot(max) range versus the 80 foot last time. All the rains have washed silt and other things into the water and corrupted the clear water. No idea how long it will take to clear up since it rains(not as heavily) here most days.

Yesterday, we floated around Zephyr cleaning her hull. With the constant exposure to water, it grows lots of green grass along the top side of her water line. With regular attention, it comes off easily but leave it for a few months and it's a whole lot harder. I strapped on my diving gear and headed for the bottom to check on our new Rocna. I'm a believer now after seeing it lying on the bottom well dug in after only moving about two feet when we backed down after dropping it. The entire plow section of the anchor is buried and only about half of the big roll bar is showing. She is well dug in an not going anywhere. Sure hope the windlass can break it free of the bottom. Guess we will see.

After diving on the bottom and cleaning the deepest part of the hull, we went in and had my tank refilled for the next dive. A nice shower and lunch at the local cafe and back to Zephyr as the winds began to blow. Into the high teens. Rain clouds came along later in the afternoon with a bit of lightening and thunder but we didn't get any of the rains that the other islands got.

We're off today for "Treasure Island" resort on another island about 8 miles from here. Supposed to be good diving there. Let's hope so. It was very disappointing here.

More coming.

Comments [0] | | More

I headed back into Lautoka this morning to get us checked out by Customs so we can head back out to Musket Cove for a week or so. Customs finally relented and now we will no longer be required to go in and check out and in when we go the whole 15 miles to Musket Cove. They have written our paperwork so that now that we are checked out, we will no longer need to check back in till we are ready to actually leave. That should be in a few months as our 6 month visas will run out. We're still in our 4 month visa period and will need to apply for the extra 2 month extension but that is always granted. While our boat can stay for 18 months, we can't(go figure).

With the check out papers on board, we will be taking off for the three hour trip. While we are there, we'll be doing some more scuba diving as well as some projects. I'll be up the mast again installing our new forestaysail halyard and putting on rubber covers on the tip of each of our spreaders. I'll be taking off the Data Marine wind instrument while I'm up there so we can mail it back to the US to see if we can get it fixed. It still tells us the direction of the wind, but not the speed and how can we brag about how bad the winds were when we are out sailing if we don't know how fast they are? Plus, we have this new shiny piece of metal(our new anchor) that needs to be put on the bow. At 88 pounds, that should be lots of fun(let alone getting the old one off).

So the next post will be from Musket Cove with all the fun things we will be doing there. I fired up the generator this morning just to make sure she still runs(no problem-started on the second pull of the cord.

Comments [0] | | More

Well, the last two days have been full of activity. Since the rain has stopped and the Ark has landed at the top of a nearby mountain top, life has returned to a somewhat state of normal(what ever that might be).

On Monday, after getting the official notice that our new Rocna 40 kilo(88 pounds for us from the US) had finally arrived, we started out for the 1045 bus for Lautoka. As we walked out the road to the bus stop, a small van came along side and offered us a ride in for the same price as the bus. That doesn't take a rocket scientist to figure it was not only a good deal, but would get us into town a good 40 minutes ahead of schedule(he picked up a few more people along the way into town). With most of the businesses closed from 1300 to 1400, we would now be able to get more done.

When the original import invoice came from Export Freight Services, there was a charge for BioSecurity in the amount of $8.00. When we got the invoice from the people that were handling the import papers(Carpenters), they upped the fee to $62.95! When I questioned them on it, they said they had made a mistake and it should have been only $30.00. When asked why there was a difference between what the importer was charging and what they wanted, they just told me it was a fee set up by BioSecurity. On the trip into town, we stopped by the BioSecurity office out on the wharf. Here is what they told us. They charge a fee of $150 to inspect everything that comes in in a container. The price is always the same. We should be charged by what percentage of the container we took up. Ever seen a container? They are huge and our anchor didn't take up that much space. BioSecurity told me to have the people at Carpenters call them. We hiked over to Export Freight Services and discussed the difference in the fees. Their suggestion--Just pay us the $8.00 and that should take care of the BioSecuity fee. No $30.00 fee, just the $8.00 fee. No problem there. There were a few more fees tacked on--forklift, lanning(?), delivery order fee, document fee,etc. All in all, between the two companies, we ended up paying an additional $139US for all the fees to get our anchor into Fiji. With the original invoice and these fees, we ended up paying $1362 for the anchor. Not bad since West Marine charges $1289 for the same thing and that is back in the US.

Once all the fees were paid and we had the paperwork we needed to pickup the anchor, it was after 1300 and the offices would now be closed so we went over to China Palace for another great lunch. Wontons, red pork fried rice and Sweet & Sour Pork. A very yummy meal. It's not as cheap as the taco carts back in Mexico(sure were great) but it sure tastes great.

We picked up a few more movies at the local video ripper store and then went to the local veggie market for some lettuce. It looked so bad that we passed. Figure we will be back in town on Wednesday or Thursday to get checked up for our next trip to the islands and we can pick some up then. We grabbed(had to wake the driver) a taxi(for what we were bringing back to the marina, it made sense) and headed over to Pacific Freight Services to get our new anchor. As we entered their warehouse, there it sat on a big wooden pallet. It was HUGE!!!! I wasn't sure we would even get it into the taxi for the ride back. Two big guys picked it up and wrestled it into the trunk and off we went with it rattling around in the back. Once back at the marina, the driver helped us get it on board the back of Zephyr. I took off the bubble wrap and there it sat, a HUGE chunk of steel to keep Zephyr right where we want her. It's like I said in an earlier post, when people passing our boat look at our anchor and laugh, I know I have the right anchor. I can already hear the laughter even before we get it in place at the bow.

Today was laundry day. Since we are heading back toward the islands in a couple of days, it will be nice to have clean clothes and sheets. It took four loads of wash and three runs of the drier to get everything done. At $6.00($3.24 US) per load of wash and dry, it came to $42.00 Fijian($22.65US) to get it all done. Not cheap but not outrageous as we have found else where in our travels. We were done just after 1300 and headed back to Zephyr for another job.

We have had a leak behind the navigation station that has been letting a good bit of water no only inside the boat, but also running over some of the electrical connection in the cabinet and inside the nav station. Well, I'd run beads of caulk over all the seams that I could see water passing through during last weekends flood. Maybe now it might be a bit drier. Guess we will see after the next storm. The block that the wires for the anchor light connect to was covered in green corrosion. I'd seen it long before I headed back to the US so I came back with two replacement blocks for the wires. First, I tried scraping and running a wire brush over all the contacts to see if I could get it cleaned up. No good. Too much corrosion. With a screw diver in hand, I headed in. Several of the screws would not come loose so I had to just cut off the wires at the fitting. I grabbed my electoral equipment and headed in to repair what I had just taken apart.

With my trusty crimper, copper laced grease(keep further corrosion out), screwdriver, wire striper, and all the electrical connectors, in I went. Now being on a boat, a job like this requires a bunch more time than a simple crimp of wires back on dry land. Here, you face a bunch of corrosion on a daily basis. For this reason, every fastener has to not only be crimped on, but I add some copper laced grease to each wire before I even do the crimp. Plus, the fasteners we use are special since the end gets heated with a heat gun(really HOT) to melt the plastic end at the end of the fitting. It shrinks down and seals the fitting. With the copper grease already in the fitting, there should be no corrosion inside of them. I also covered the place where the screws go into the fitting and the end of each "eye" as they get screwed to the block. I even covered the screws that hold the "eye" to the block. If this corrodes, I'd be amazed. I've turned on the anchor light so we will see later tonight(on a solar cell) when it comes on.

Off for a late shower and now another night at the movies. We watched "The Tourist" with Johnny Depp and Angelina Jolie last night. If you haven't seen it, I highly recommend it. Great story.

More to come so stand by.

To get a idea of the size of the anchor, that's a big 5 gallon bucket behind it. It makes the bucket look small.

Comments [0] | | More

Buying things in stores in Fiji is easy for most cruisers. We either whip out a credit card or we make a trip to the local ATM and get a bunch of cash. No problem. For locals, it another matter. I was looking through one of the local papers(Fiji Times) and spotted an ad from "Courts". They are one of the larger appliance and home furnishing stores here in the islands. I scanned the prices in the ad. Not too bad considering that everything they sell has to be shipped into town on one of the many freighters that arrive here. Each and every piece is subject to a hefty import tax so that tacks on even more to the price.

If you purchase an item on credit, depending on the price, a set of time is allowed for paying off the principle. Sometimes it's 52 weeks and many times for the more expensive things, it can be up to 156(three years)weeks. It's never longer than that. Take for example a combo package of a toaster and a coffee maker. It's listed for $149 Fijian. Payments are only $3.60Fijian for 52 weeks. That works out to $187 for the final price of $187. That makes for an interest rate of 25% on what you have bought. An Akita 42" LCD TV runs $2299. With the interest after the three years they allow to pay it off, the final price comes to $3556.00!!! Your final price is 59% over the advertised price! Try that in the US and I don't think you'd have any customers.

From what I've read, the economic crunch has really hit the Fijian people. The base hourly wage here is only $2.80 Fijian($1.51US). I had a conversation with one of the woman that manage the marina the other day about one of the girls in the office that left to get married. The woman manager asked me if it's was true that we Americans tell our kids that they can grow up to be anything. My answer was "Yes we do". Her response was that that was not how it was in Fiji. There are not a tremendous amount of jobs available in Fiji where a person can truly excel and grow and make a bunch of money. The girl that left(maybe making $3.00 Fijian) is a licensed pilot! She can't get a job because there aren't any available so she was forced to take what she could. With a nation faced with that dilemma, many people can get behind in their payments and loose possession of their goods. With interest that high, a native must be sure that they can cover the debt. Not an easy thing to do out here. Out here, most people live a simple life and from what we have seen are quite happy. Smiling faces are everywhere and always the cry of "Bula"(hello) from everyone we pass in town as well as out here.

Another thing we have learned is that Fiji is a bargaining country. Just because an item is marked at $19.95, that doesn't mean that that is the price you will be paying. I bought two shirts at a store in town a few weeks ago. Each was marked at $26.95. When I went to pay for them, the clerk behind the counter told me he would sell them to me for $24.00. I hadn't even asked for a better price, he just gave it to me. We Americans are used to seeing a price on an item and just paying for it. That's not the way it is out here. Going to the vegetable market in the center of town is an education in itself. EVERYONE bargains there. The veggies may look wonderful and the asking price(by American standards) is quite reasonable. BUT--they expect you to bargain. They may be asking $3.00 for a bunch of carrots. You counter with $2.00. He may go for it or he may not. It's not a problem wether he will go for the $3.00 or not as there is always another vendor two steps away that might. I really have to work on my bargaining skills. They stink. I, like most Americans are simply used to paying what the marked price is. It's not that way out here.

A couple of months ago, the taxi's all raised their prices(approved by the government and urged by their Union) by 100%. There was no outcry until it happened because very few people knew it was even going to happen. Traveling from the marina to town went from $7.50 to $15.00 one way. A bus ride costs only $1.60 each way. We have taken very few taxis since we have been here, not necessarily because of the price increase(though it's a big reason) but we like to travel and meet the natives that ride the bus. Once the prices went up on the taxis, many more people started taking the buses about the island. Amazingly, the price even went down from $1.70 to $1.60Fijian. With the bad economy, the taxi union has made it much tougher for the average person to afford taking a taxi. When we are in town we've seen the majority of the taxis empty(unless it's raining). A couple of days ago, we were waiting at the bus stop just outside the marina with Christine off Teka Nova. She had never taken a bus to town in the two months that they have been in the marina. As we waited, a taxi came by and asked if we wanted a ride to town. Since we were giving Christine a lesson on taking the bus, we declined. To try and entice us into his cab, he offered to drop his price to $1.60 per person for the ride($4.80). Way below the normal price. Now all taxis have the meters like they do in the US, just most of the drivers don't drop the flog on them unless they have to. This way, they can bargain on the fares they charge. Is it illegal? You bet it is and they could get in a ton of trouble not only with the union, but also the government that wants their cut of the fare that is taxed. If the flag is not dropped on the meter, there is not record of the trip. It's all pure profit for the driver.

It's tough in the US and it's tougher out here.

Comments [1] | | More

It's finally letting up with just a few sprinkles a few minutes ago. I turned a bucket right side up on the stern deck yesterday about noon and there is well over an inch of rain in it now and that was after most of the rain was over so heaven only knows how much we finally got. One of the locals that owns a boat next to ours had planned on going home last evening but all the roads to his house were washed out so he's stuck here for a while. The water into the marina is now off. Not sure why. It was off yesterday afternoon when I went up to take a shower but came back on later. We'll see how long it takes to get it back on as it's now Sunday and it's illegal to do most any kind of work today. Glad we filled our tanks a week ago.

Today, it's supposed to clear out a bit with only a 60 percent chance of showers.

Yesterday, during the downpour, we went over to Terry and Christine's boat Teka Nova for high tea. Wow, what a presentation by these Brits. Sandwiches and scones and tons of assorted pastries. A beautiful feast. Afterwards, the four of us came back to Zephyr and we learned how to play Mexican Train dominos as well as a game called Bananas. I'd heard of Mexican Train but never Bananas. Did fair in the dominos but sucked at Bananas. Too fast a game for me. Just couldn't keep up with the play. Oh well, maybe next time I'll do better.

Today, a few projects plus I now have to see if I can find a new chart plotter since Garmin has stopped supporting the software that runs in ours. It's hard to get motivated to do a job when it's pouring outside.

Comments [1] | | More