Prepking Dumps

Q. A software tester is responsible for:
A. Creating vision documents and identifying software defects.
B. Identifying software defects using static analysis tools.
C. Identifying misunderstood or missing requirements, as well as software defects.
D. Writing software prepking documentation and identifying software defects.
Answer: C

Q. Which of the following software development models should a team use if it wishes to add explicit verification and validation steps to every phase of the classic waterfall lifecycle?
A. Modified waterfall.
B. Agile model.
C. Spiral model.
D. V-Model.
Answer: D

Q. In the Whole Plan Model tool, the Model pane reports a summary of savings (or cost) in time and resources between the Baseline and To Be states. This information is expressed in absolute numbers, dollars, and:
A. Percentage.
B. Relative cost.
C. Employee hours.
D. Resource cost.
Answer: A

Q. A software tester is responsible for identifying:
A. Security defects but not usability defects.
B. Security and usability defects, but not localization defects.
C. Functionality and localization defects.
D. Functionality and prepking usability defects, but not security defects.
Answer: C

Q. Exceptions are ____ in application code, outside of the ordinary scope of application operation.
A. Leaks.
B. Propagations.
C. Errors.
D. Triggers.
Answer: C

Q. An iSeries has three partitions. The primary and one secondary are at V5R1, the other secondary is at V4R5. An external switchable DVD and QIC tape are required. A failure occurs when installing the V4R5 partition from CD with the DVD-RAM drive. Which of the following is the cause?
A. The DVD-RAM cannot read CD media.
B. The DVD-RAM is not supported at V4R5 from the distribution media.
C. The tape drive must be the first in the daisy chain on the magnetic media controller.
D. The V4R5 media prepking should be virtualized on the primary partition and loaded from the primary to the secondary.
Answer: B

Q. A customer has three AS/400 systems: a Model 720, a Model 270, and a Model 170, all are on V5R3. They want to consolidate all the servers into an eServer i5 520 with three partitions. The basic configurations include:
A Model 720 with:
.1 FC #2722 twinax
.2 FC #2745 two-line communications
.1 FC #2838 Ethernet
A Model 270 with:
.1 FC #4746 Twinax card
A Model 170 with:
.1 FC #2721 Twinax / communications card
.FC #2838 Ethernet
. FC #2850 IXS
Which of the following is a list of communications and LAN features that can be migrated to the new i5 520?
A. FC #2722, #2745, #4746
B. FC #2745, #2838, #4746
C. FC #2722, #2745, #2838, #4746
D. FC #2745, #2838, #4746, #2850
Answer: B

Q. A customer wants to move memory from an OS/400 partition to a Linux partition each night. Which of the following procedures will accomplish this task?
A. Use SST to move the memory features to the Linux partition.
B. Use Advanced Job Scheduler to schedule the dynamic memory move.
C. Shut down the Linux partition, move the memory and reboot the Linux partition.
D. Use Management Central - Scheduled Tasks to schedule the move between the endpoint partitions.
Answer: C

Q. A customer has an eServer i5 520 with a #0595 running with a total of 8 drives in disk bay slots 1-4 and 7-10. The system is being partitioned and the disk drives in the #0595 are being set up for the new partition. After IPLing the partition from CD, the Install Licensed Code option fails with a message that "No valid load source disk is available." Stand-alone DST shows the disk IOA and drives. Which of the following is the most likely cause of the problem?
A. The disk IOA must be in a slot adjacent to the IOP.
B. Use the HMC to set the SCSI address for the load source drive.
C. The disk drives must be in consecutive disk bays starting with bay 1.
D. One of the disk bays must have the connector cable moved to IOA port 0.
Answer: D

Q. A customer is planning to consolidate the following systems onto a single eServer i5 LPAR system with one partition for each migrated system. The existing tape drives are also listed:
. i820 with 3590-E11 and 3581-L23 tape drives
.iSeries 720 with 3580-H13 tape drive
.iSeries 170 with 7208-345 tape drive
.RS/6000 system prepking 000-365 with 3580-H11
The i5 LPAR system will also have a Linux partition. The backup requirements are:
. Any i5/OS partition should have access to each of the tape drive types (3590, LTO, 8mm);
.the AIX and Linux partitions only require LTO access;
.the AIX and Linux partitions should be able to perform file level backups; and
. the number of tape drives and tape I/O adapters should be minimized.
What is the minimum number of tape I/O adapters required in the i5 system?
A. 3
B. 4
C. 5
D. 6
Answer: B